SEARCH

Cooling pack off of a 2017 Kenworth T800 run for just 144,569 miles, non-wrecked. Comes with condenser, radiator, fan & shroud, and reservoir. Unit is in very good condition. OEM P/N F31-6101-2401510

Steel OEM bumper pulled from a 2015 Kenworth T800 run for just 23k miles, non-wrecked. Bumper measures 14" tall at center. Fog lights have been pulled since pictures were taken, NOT included . Hendrickson P/N L14080245

Right side rear fill fuel tank pulled from a 2013 Kenworth T800, non-wrecked. Tank is in good used condition, see pictures. 75 gallon capacity, tank measures 36" weld-weld with a 24.5" diameter. OEM P/N K444-0457N0102U075 *straps and saddles available for purchase separately*

"Pogo" with lines pulled from a 2006 Kenworth T800, non-wrecked. Part is in good used condition, includes components pictured. OEM P/N K326-145

Heater core block / housing pulled from a 2014 Kenworth T800. Unit is in good used condition, see pictures. OEM P/N F66-1421

Front right quarter fender off of a 2015 Kenworth T800 (non-wreck) run for just 23,000 miles. Has cutout for air cleaner. Paint is in great condition. P/N L35-1030-1R Mud flap included.

Fan clutch off of a Cummins ISX engine pulled from a 2013 Kenworth T800, non-wrecked. Part is in good used condition, see pictures. Horton brand P/N 79A9897 , P79A9897

LEFT HAND SIDE Spring hanger / frame horn / drive bracket out of a 1989 Kenworth T800. P/N is K058-511 for the left (with 479L stamped above). In very good condition - no damage, bends, or dents. Material is aluminum. $325 per side RIGHT SIDE HAS SOLD 9/11/23

Left side front fill fuel tank pulled from a 2013 Kenworth T800, non-wrecked. Tank is in good used condition, see pictures. 100 gallon capacity, tank measures 47.5" weld-weld with a 26" diameter. OEM P/N K444-0486N0102B100 *straps, saddles and steps available for purchase separately*

Right and left hand spring hanger / frame horn / drive bracket off of a 2006 Kenworth T800. Part number B11-1025 for left and B11-1025R for right. Has a few other stamped numbers as pictured. Material is aluminum. No bends, dents, or damage. $250 each

Electronic chassis control module pulled from a 2013 Kenworth T800, non-wrecked. Control module is in good used condition, see pictures. OEM P/N Q21-1142-001-001

Leaf spring pulled from a low mileage 2013 Kenworth T800, non-wrecked. Part has some surface rust but is in good used condition, see pictures. OEM P/N B81-6013 REV D

OEM cool pack assembly pulled from a 2013 Kenworth T800 with ISX engine, non-wrecked. Pack is in good used condition, includes radiator, CAC, condenser, etc. OEM P/N listed on core F31-6101-2101510/N

Front engine mount pulled from a 2008 Kenworth T800, non-wrecked. Mount was set up with Cummins ISX engine. Good condition as pictured, steel material. OEM P/N K107-786 / K107-786-A

Radiator core support crossmember pulled from a 2013 Kenworth T800, non-wrecked. Support is in good used condition, shows general light signs of wear/use. OEM P/N A24-1392 secondary stamped OEM P/N A24-1213 REV A

Right hand spring hanger / frame horn / drive bracket pulled from a 2013 Kenworth T800, non-wrecked. Material is aluminum. No bends, dents, or damage. OEM P/N B11-1025R REV B

Left hand spring hanger / frame horn / drive bracket pulled from a 2013 Kenworth T800, non-wrecked. Material is aluminum. No bends, dents, or damage. OEM P/N B11-1025 REV B

Right side cab mount pulled from a 2013 Kenworth T800, non-wrecked. Part is in good used condition, see pictures. OEM P/N A85-1277-001R or A85-1277-002R REV A

PACCAR - Bosch power steering hydraulic & fuel lift pump combination assembly pulled from a 2016 Kenworth T800 with an MX13 run for 47,679 miles. No core charge, air compressor can be purchased separately if in stock. Multiple searchable part numbers listed: 1885525 - 8695 955 162

Left side cab mount pulled from a 2013 Kenworth T800, non-wrecked. Part is in good used condition, see pictures. OEM P/N A85-1277-001 or A85-1277-002 REV A

Right side front cab mount bracket pulled from a 2010 Kenworth T800, non-wrecked. Part is in good used condition, see pictures. OEM P/N K235-1825R

Right side cab mount pulled from a 2014 Kenworth T800. Part is in good used condition, see pictures. OEM P/N A85-1277-001R or A85-1277-002R REV A

Left side front cab mount bracket pulled from a 2010 Kenworth T800, non-wrecked. Part is in good used condition, see pictures. OEM P/N K235-1825

Left side cab mount pulled from a 2014 Kenworth T800. Part is in good used condition, see pictures. OEM P/N A85-1277-001 or A85-1277-002 REV A

Right hand spring hanger / frame horn / drive bracket off of a 2014 Kenworth T800. Part number B11-1026R for right (also has 20808AA stamped below P/N). Has a few other stamped numbers as pictured. Material is steel. No bends, dents, or damage. (Left side has sold)